For New and Existing Concrete, and Concrete Pavers

The Armor AX25 is a solvent based siloxane acrylic high gloss sealer that is designed to seal, enhance, and protect a variety of exterior concrete and concrete paver surfaces. It penetrates deep into the surface where it chemically bonds to the pores of the concrete and pavers, creating a long lasting, non-yellowing, breathable finish that enhances dull or faded surfaces.

Multi-Purpose Sealer & Coating

The Armor AX25 is a siloxane acrylic sealer. The siloxane component penetrates into the concrete where it chemically reacts to form a barrier below the surface. The acrylic component bonds to the surface where it forms a durable, lasting, high gloss surface film. Our proprietary formulation works hard to protect your concrete and pavers above AND below the surface. It is also ASTM tested and approved, and can help aid proper curing when applied to new concrete.

Uses & VOC Regulations

Uses:

The Armor AX25 is designed for use on poured concrete, stamped concrete, aggregate concrete, and concrete paver surfaces. It can be applied to unsealed surfaces, and surfaces previously sealed with a solvent-based acrylic. It can be applied to new concrete to help with proper curing. It is a great choice for driveways, walkways, patios, concrete floors, pool decks, and more!

Do not apply this product to red clay brick, slate, flagstone, or other types of natural stone. If you are looking to seal red clay brick, slate, flagstone, or any other type of natural stone, consider the Armor WL550 or the Armor SX5000 WB.

VOC Regulations:

The Armor AX25 is 700 VOC: The 700 VOC formulation can be used in every state except AZ, CA, CO, CT, DC, DE, IL, IN, MA, MD, ME, MI, NH, NJ, NY, OH, PA, RI, UT, VA.

Please note that the above information is for informational purposes only, and based solely on information known to Foundation Armor at the time this page’s publication. VOC regulations can change, and can vary by country within each state. Please consult your federal, state, and local regulations to ensure you are using a VOC compliant product. If you live in a restricted state, please consider the Armor AR500 or Armor LV25 instead.

How To Apply

The Armor AX25 can be applied with a 3/8-1/2” nap roller, or a solvent resistant HVLP sprayer. For a consistent wet look and high gloss finish, apply two coats spaced 24 hours apart.

Time Of Day: The Armor AX25 should only be applied in the early evening when air and surface temperatures are declining, and when the sun is no longer positioned over the surface. To avoid bubbling and hazing, do not apply in the morning or middle of the day.

Surface Preparation: The Armor AX25 should be applied to a completely clean and dry surface. If the surface was cleaned with water or pressure washed prior to application, allow the surface to dry for at least 24 hours before sealing. While pressure washing the surface is typically sufficient, spot treatment may be necessary for deep or older stains.

The Armor AX25 is designed specifically for use on unsealed concrete and concrete paver surfaces, as well as concrete and concrete pavers previously sealed with a solvent based acrylic. If the concrete is smooth or trowel finished, and doesn’t quickly and easily absorb water, other surface preparation may be required to open up the surface pores, such as acid etching or grinding. The Armor AX25 should not be used to seal clay brick, red Chicago pavers, flagstone, slate, or natural stone. If you are looking to seal clay brick, red Chicago pavers, flagstone, slate, or natural stone, consider instead of the Armor WL550 or the Armor SX5000 WB. Note About Sealing Pavers: Please note, while the Armor AX25 can be applied over paver joints, it is not designed as a bonding agent and will not harden or bond the loose sand in the paver joints. If applying with a roller, loose sand in the joints may cling to the roller and be redistributed across the pavers. For best results, apply first coat with a sprayer if you are applying to pavers with loose sand in the paver joints.

When applying to porous pavers, gloss level may be reduced, and more material may be required to achieve desired finish.

Mixing Opaque Color Packs: Do not exceed more than 6 ounces of color per gallon of sealer. Stir color well before adding to sealer, then once added to sealer, stir again, ensuring color is evenly mixed. Once cured, will cover like a paint—you will be left with an opaque colored finish.

Mixing Semi-Transparent Color Packs: Do not exceed more than 1 ounce of color per gallon of sealer. Stir color well before adding to sealer, then once added to sealer, stir again, ensuring color is evenly mixed. Once cured, will offer a semi-transparent tinted finish.

Adding Non-Slip: For added surface traction, the Armor Non-Slip additive can be added. The ultra-fine, fine, and coarse Armor Non-Slip additives works best in the Armor AX25. Applying the Ultra-Fine: Slowly drill mix 3-6.5 ounces of non-slip additive per gallon of sealer, until completely blended, then apply. For Fine and Coarse: When applying the second coat, add the non-slip additive to the coating using a broadcast spreader, and back roll to encapsulate the non-slip additive.

Clean-Up: Use Xylene or acetone. Dispose of containers in accordance with local and federal regulations.

Product Removal: Dried, cured sealer may be removed with a the Armor CR100, or by using a diamond grinding method, sandblasting method or similar mechanical action.

Coverage

Porous Surfaces: Up to 175 FT2/gallon in one coat.

Smooth Surfaces (once properly prepped): Up to 200-225 FT2/gallon in one coat.

Coverage will vary depending on porosity, surface condition, application method, and the amount of material applied by the applicator. The above coverage rates are estimates and will vary. Two coats are suggested for even coverage and appearance. Please note, if it is your first time sealing pavers, or an overly porous surface, a third coat may be required.